What checks should you do before using a sling?

How often is a harness inspected?

What is the point of inspecting your protection equipment? Personal safety and fall protection equipment, as well as any PPE provided by your company, must be inspected periodically by a COMPETENT TECHNICIAN [and by yourself if you don’t want to be surprised!]

If you are really worried about the expiration date of your safety harness, the best thing to do is to follow the applicable regulations and to keep up to date with the epis through agendas, calendars, and periodic reviews of the equipment.

In conclusion: It is the owner, the person responsible for safety in the company or PRL and finally the user himself, who must REVIEW the harnesses every time they are going to be used or change of user or undergo modifications.

One thing is that the company can justify that it hires an external and qualified audit to check the equipment, and quite another is the day to day, where experience and responsibility are the real prevention of occupational hazards.

Just as no one would think of using a motorcycle helmet that has received a strong impact after a traffic accident, it is not possible to use a fall arrest harness or energy absorbers that have fulfilled their function by braking the impact of a fall.

When should a harness be discarded?

A harness that is damaged should not be repaired, it should be marked as unusable. In addition, if the harness has already withstood a person’s fall it should also be replaced. Other signs that it is best to discard the harness are: If there are cuts in the webbing.

Read more  Why is it important to follow proper procedures?

How long does the certification of a harness last?

The fall protection industry recommends two to three years as the useful life for a harness or belt in use. For shelf life, it recommends seven years. In the military, seven years is the estimated in-use life for nylon products.

How is the harness checked?

Check that belts and straps are not cut, broken, twisted or fragmented. Check for damage caused by fire, acids, solvents or other corrosives. Metal parts of the equipment must be free of rust, cracks, sharp edges and roughness.

Harness damage

One of the most frequent mistakes when working with fall protection systems, regardless of the type, is not checking the safety of the connectors. Leaving a carabiner with an open thread can have serious consequences.

During fall arrest, the impact can generate oscillations in the rope which, in the worst case, can cause the rope to work directly on the gate: if the gate is open, the probability of the rope slipping out of the carabiner increases considerably.

This point is particularly important: extreme temperatures, rain and especially wind can endanger the life of the exposed worker and must be taken into account in work planning.

On many occasions, when these weather conditions are not clearly adverse, it is difficult to establish in a definitive manner when they are so unfavorable as to suspend the work or the task.

In rope access work, the fall factor must be controlled at all times, ensuring that the fall arrest device is as high as possible. And when lateral displacements are possible, the pendulum effect must be taken into account and avoided to the greatest extent possible.

Who certifies harnesses?

Harnesses, slings, connectors and lifelines manufactured and marketed by 3M / Capital Safety under the Arseg, DBI-SALA and Protecta brands are certified under international standards (ANSI) and do not have a fixed expiration date.

Read more  Can a deputy buy property?

Who certifies work at heights?

Certification for Work at Heights – Unimsalud S.A.S.

What are the parts of a harness?

They mostly consist of three D-rings for attaching the connectors to the anchorage, leg loops, adjustment points, pads and hardware. Optionally they can have a fourth chest D-ring for added security, although this is not mandatory.

Harness inspection

Mainly we have 6 references with implications on the subject of fall protection equipment inspections or verifications. Here are the most relevant extracts from each of these legislative and regulatory references.

1. The employer shall adopt the necessary measures to ensure that work equipment is suitable for the work to be carried out and suitably adapted for this purpose, so as to guarantee the safety and health of workers when using it.

Royal Decree 2177/2004, of November 12, 2004, which amends Royal Decree 1215/1997, of July 18, establishing the minimum health and safety provisions for the use of work equipment by workers, with regard to temporary work at heights.

2. The employer shall take the necessary measures to ensure that work equipment subjected to influences likely to cause deterioration that could lead to dangerous situations are subject to periodic checks and, where appropriate, tests, in order to ensure compliance with safety and health provisions and to remedy such deterioration in a timely manner.

Who can certify anchor points?

After installation, fixed anchors must be 100% certified by a qualified person, through a methodology tested by recognized national or international authorities. (resolution 1409 of 2012).

Who can certify an anchor point?

GecaB Colombia S.A.S. designs, installs, inspects and certifies anchor points according to the current legal regulations in Colombia (RESOLUTION 1409 DE 2012).

Who certifies a lifeline?

Only those professionals, authorized to do so by the manufacturer of the systems to be installed, can install and certify a lifeline in accordance with legal requirements.

Read more  What policies and procedures do I need as a childminder?

Harness inspection pdf

First of all, we must remember that working at heights is the work that takes place at a height of more than 1.80 meters and that, due to these characteristics, implies the need to protect oneself from a fall, for which a safety harness is used, which is a protection equipment, whose main objective is to stop or slow down the free fall of an individual.

Most harnesses consist of nylon or polyester straps or tapes, which are adjustable both in shoulders and legs, which distribute the user’s weight across the chest and hips, and also have rings which are connected to a safety line.

Therefore, when working at a different level of more than 1.80 meters, it involves certain risks such as falls, which due to the height are likely to cause injuries, so to avoid falling into the void, the use of a safety harness is required, which by the way its use in these conditions is mandatory.